![]() ![]() \renato 64.124.57.5 iPhone OS:6.0 10.10.10.1 64.124.57.5 exist none Oct.02 06:38:33 Oct. I have installed MS Loop-back adapter and have given it a static IP: 10.10.10.9 my laptop is configured as 10.10.10.30, and my gateway is 10.10.10.1 i can ping the loop-back NIC from my laptop. It always resolves to 127.0.0.1, known as the loopback address loopback is a special IP address that. Many network administrators, programmers, and IT technicians also refer to it as the local computer or home computer. \renato PAN01347 Windows 7 (Version 6.1 Build 7601 Service Pack 1)10.10.10.2 64.124.57.5 exist none Oct.02 06:04:01 Nov.01 06:04:01 2589926 9641 In computer networking, localhost is the default name (hostname) for the computer youre logged into or working on. GlobalProtect Name : gp-gateway (2 users)ĭomain User Name Computer Client Private IP Public IP ESP SSL Login Time Logout/Expiration TTL Inactivity TTL > show global-protect-gateway current-user The password in the profile will need to match with the authentication method chosen (ie ldap, kerberos,localdb, etc).Ĭonfirm access via your Global Protect client as well as your mobile device. This will be utilized when configuring the VPN profile on the mobile devices.Ĭreate the VPN Profile on the iPhone/iPad using the shared secret configured in the previous step. ![]() In this example, the gateway service group is utilized and used to forward traffic to 10.1.1.2, the loopback.2 interface previously configured.Įnable 'X-Auth Support' on the gateway and create a Group Name and the Group Password respectively. Below this rule, another rule is created to the gateway allowing ike, ipsec, panos-global-protect, ssl and web-browsing respectively.Ĭreate the NAT policy which will forward traffic to the second loopback (loopback.2) interface. Here GP portal is accessed on port 7000 instead of port 443. The two custom services are added in addition to the predefined service-https to the gateway service group profile.Īdd the services to a service group objectĪs noted in the prior KB article, a rule is needed for the Portal page to redirect that traffic on a non-ssl standard port to our first loopback interface. In this example, services were created destined for ports 500 (ike/ciscovpn), 4501 (ipsec-esp-udp). These services will be natted to our Gateway loopback interface. PING 10.1.1.2 (10.1.1.2) from 99.7.172.157 : 56(84) bytes of data.Ħ4 bytes from 10.1.1.2: icmp_seq=1 ttl=64 time=0.126 msĦ4 bytes from 10.1.1.2: icmp_seq=2 ttl=64 time=0.068 msĪssign loopback interface as the Portal addressĪssign loopback.2 interface as the Gateway addressĬreate the following services and add them to a service group. Make sure the untrust interface can ping the loopback. You'll need to create a second loopback interface in addition to the first loopback interface used for the Portal. Please follow Knowledge Base article How to Configure GlobalProtect Portal Page to be Accessed on any Port with one caveat. ![]() If you only have one public-facing IP address, and you wish to host SSL-based applications, such as OWA on that IP, the following information provides the configuration steps for doing so. Did your DNS undergo testing because a many times loopback entry tests ability to process Web requests without actually sending any messages out. The following example shows valid IP address configurations on two loopback interfaces.In addition to using a non-https Global Protect Portal, you can access an associated Gateway on a configured loopback interface. ![]() Up to thirty-two IP addresses are supported on a loopback interface. You can configure multiple IP addresses on a loopback interface ( lo0 to lo7). In the same way, if you configure a loopback interface ( lo1) with IP address 172.16.101.8, you cannot configure another loopback interface ( lo2) with IP address 172.16.101.8. This means that the address cannot be used by a VLAN interface or another loopback interface.įor example, if you configure a VLAN with IP address 172.16.100.8/24, you cannot configure a loopback interface with IP address 172.16.100.8. The maximum number of IP addresses supported on a switch is 2048, which includes all IP addresses configured for both VLANs and loopback interfaces (except for the default loopback IP address 127.0.0.1).Įach IP address that you configure on a loopback interface must be unique in the switch. Loopback interfaces share the same IP address space with VLAN configurations. You can configure a loopback interface only from the CLI you cannot configure a loopback interface from the WebAgent or Menu interface. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |